Friday 16 October 2009

SUBARU IMPREZA BUGEYE DASHBOARD CLOCK REPAIR

A common fault on subaru impreza wrx dash board clock not working it stems from a resistor inside clock and here is my guide to show you how to do it yourself .

The way you have to look at it is that the thing is broken anyway and its worth a shot.

you will need

A soldering iron with fine tip

Multicore solder (fluxed)

Feeler gauges (you will see why)

Nerves of steel
Here goes,

First take out dash clock on dash put your fingers under hood and pull up from screen side









Its in tight a good tug will release it













Thats the back clips off now the front ones

put your fingers down left hand side and pull like your life depends on it. Its in tight so nerves of steel required, you wont break any clips (Trust me)






And pull

















Thats one side done now pull like crazy on the other side its in hard..... be brave!

Now with surround out disconnect the wiring harness plug from clock

Now removing clock itself is tricky, get some feeler gauges and slide them in side shown in picture
This is in really tight and twist it so you are forcing gently the clock unit backwards away from the surround not up or down









this is in really tight be brave and be carefull not to lever in the front part of clock housing as this is the screen


once you get this side out the other side will come out using a bit of tugging bend the clip back using fingers and out it pops

Now seperate the face from the back do this on a table not in the car as the buttons will fall out. just move the tabs gently up these are brittle so be careful





see tabs just lift them gently and pull face off










see resistor pictured left R510




Now once inside you can see resistor pictured with ball point pen this is the one, use a fine tipped soldering iron and a dab of solder on the end contacts. It will look like nothing is wrong with it but if you wiggle it you will see which side is loose but i re did both as a precautionary measure.

Now pop it all back together and try it out


It worked for me


however i cant be held responsible for your own actions and damage caused be carefull and if in doubt ask a grown up for help and dont burn yourself soldering irons are hot!

Best of luck feel free to add your comments

16 comments:

  1. This repair worked for me! I was surprised that I had the identical problem, down to the exact same defective solder joint on the same surface mount resistor. Although it has been less than 24 hours, it seems to be fixed. Thanks

    ReplyDelete
  2. This Repair also worked for me :) cheers for the write up!

    ReplyDelete
  3. Sorted my fault as well, seen a service for £10 on ebay to do this ...it only takes 5 mins from pulling the unit out to plugging it back in...cheers for write up...nice 1..

    ReplyDelete
  4. i just fix that today as well brilliant thanks for write up

    ReplyDelete
  5. thanks allot man i had the same problem and now i fixed it :P rip

    ReplyDelete
  6. Thank you! From New Zealand.

    ReplyDelete
  7. Thanks again from New Zealand, worked a treat for me.

    ReplyDelete
  8. Careful-- when pulling up on mine, it cracked & broke into a few pieces. I was able to epoxy them back together, but still...

    ReplyDelete
  9. Its awesome! I had the same problem since 2 days ago - and I fixed it this morning. Thanks!

    ReplyDelete
  10. Took ten minutes to fix! I have been waiting months to sort out that clock. Thank you.

    ReplyDelete
  11. mine cracked where can i get new plastic panel ?

    ReplyDelete
  12. Thanks man, had the same exact problem and your tutorial worked like magic. I now have a clock in my car something the dealer was asking me to get a new clock.

    ReplyDelete
  13. I repaired my impreza gx last year and my Subaru wrx this year same fault
    thanks a lot

    ReplyDelete
  14. Just a note for others out there - check all three resistors. There are two 300 and one 510 ohm resistors and any one of them may have a bad solder joint. If in doubt, touch up all the solder joints on the resistors (carefully, don't add any if there is already some there).

    Thanks for the write up - getting the trim off the interior of a car is always the hardest part and this is the easiest way I've seen so far.

    ReplyDelete
  15. Thank you so much. I bought my 2001 Impreza RX last week and the clock wasn't working. It irked me so I thought I'd look up to see if it was fixable, found your tutorial and it worked! just the way you said. I did it and I'm a woman! :) Thank you!!

    ReplyDelete
  16. Worked for me as well. All 3 large resistors needed soldering. Thanks for the detailed instructions.

    ReplyDelete